How To Replace Battery In Honda Key Fob
Did you know that an estimated 85% of new cars sold in the US come equipped with keyless entry systems?
Millions of drivers nationwide rely on key fobs to access their vehicles daily. However, as with any electronic device, the battery in your Honda key fob will eventually run out of juice and require replacement.
In fact, according to recent studies, the average lifespan of a key fob battery is only around 2-3 years.
The good news is that replacing the battery in your Honda key fob is a straightforward process that can be done at home with just a few basic tools.
In this article, we’ll guide you on How To Replace Battery In Honda Key Fob, saving you time and money in the long run.
So, without any further ado, let’s get into it!
What type of battery does a Honda key fob take?
Before learning how to replace the battery in your Honda key fob, you must know what battery you need.
The type of battery required for a Honda key fob can vary depending on the make and model of your vehicle.
However, most Honda key fobs use a CR2032 lithium coin cell battery, commonly used in many electronic devices.
It’s important to use the correct type of battery when replacing the battery in your Honda key fob to ensure proper functioning.
Before purchasing a replacement battery, check your owner’s manual or consult a trusted mechanic to confirm the correct battery type for your specific Honda key fob model.
Necessary Tools and Materials Required
To replace the battery in your Honda key fob, you will need a few basic tools, including a small flathead screwdriver and a jeweler’s screwdriver. The small flathead screwdriver will be used to pry apart the two halves of the key fob, while the jeweler’s screwdriver will be needed to remove the small screw that holds the key fob together.
In addition to the tools, you will also need a replacement battery. As mentioned earlier, most Honda key fobs use a CR2032 lithium coin cell battery. These widely available batteries can be purchased at most electronic stores or online retailers.
Check the owner’s manual or consult a trusted mechanic to confirm the correct battery type for your specific Honda key fob model before purchasing a replacement battery.
With these necessary tools and materials, you can easily and quickly replace the battery in your Honda key fob, saving you time and money in the long run.
How To Replace Battery In Honda Key Fob
Now, let’s take a deep dive into the solution part of this comprehensive guide and understand the important steps to changing the battery in honda key fob.
Step 1: Opening the Key Fob
The first step in replacing the battery in your Honda key fob is to open the key fob casing safely. This can be done by following these steps:
Locate the small notch on the side of the key fob casing. Insert the small flathead screwdriver into the notch and gently pry apart the two halves of the key fob.
Once the two halves are separated, use the jeweler’s screwdriver to remove the small screw that holds the key fob together.
During this process, be careful not to lose the screw or any other small parts that may fall out of the key fob casing.
Some Honda key fobs may have hidden latches or screws that must be released before opening the casing. Refer to your owner’s manual or consult a trusted mechanic if you are unsure how to safely open your specific Honda key fob model.
Following these steps, you can safely and easily open the key fob casing and access the battery compartment.
Step 2: Removing the Old Battery
Once you have safely opened the key fob casing, the next step is to remove the old battery. Follow these steps to remove the old battery from your Honda key fob:
- Locate the battery compartment inside the key fob casing. The battery compartment will usually be a small round or rectangular on one side of the key fob.
- Carefully remove the old battery from the battery compartment. You can use the small flathead screwdriver or your fingernail to pry the battery out of the compartment gently.
- Be sure to dispose of the old battery safely and environmentally-friendly properly. Many electronic stores or recycling centers offer battery recycling services.
Possible challenges when removing the old battery may include difficulty accessing the battery compartment or difficulty removing the old battery due to corrosion or other factors.
To overcome these challenges, use a cotton swab or toothbrush to clean the battery compartment and remove any corrosion, or use a pair of needle-nose pliers to grip and remove the old battery gently.
If you still have difficulty, consider consulting a trusted mechanic or electronics specialist.
Step 3: Understanding Battery Polarity
Before installing the new battery in your Honda key fob, it’s important to understand its polarity and significance. Battery polarity refers to the positive and negative terminals on the battery and their corresponding positions in the battery compartment.
In most Honda key fobs, the battery’s positive terminal will be marked with a plus sign (+), while the negative terminal will be marked with a minus sign (-). It’s important to properly identify the positive and negative terminals to ensure proper functioning of the key fob.
To identify the positive and negative terminals, look for the old battery’s markings or the battery compartment. If the markings are not visible, you can use a multimeter to test the terminals and identify the positive and negative connections.
Once you have identified the positive and negative terminals, you can install the new battery in your Honda key fob.
Read Also Our Experts Article : How To Remove Window Tint From Car
Step 4: Inserting the New Battery
After identifying the positive and negative terminals, the next step is to insert the replacement battery into the battery compartment.
Follow these steps to insert the new battery in your Honda key fob:
- Ensure the battery compartment is clean and free of debris or corrosion.
- Carefully insert the new battery into the battery compartment, aligning the positive and negative terminals with their corresponding positions.
- Press the battery firmly into place to ensure proper contact with the terminals.
- You can reassemble the key fob once the new battery is securely in place.
Step 5: Reassembling the Key Fob
To reassemble the key fob, follow these steps:
- Ensure that all small parts, such as the small screw or any other pieces that may have fallen out during the battery replacement process, are accounted for and properly placed.
- Carefully align the two halves of the key fob casing and press them together until they click into place.
- Use the jeweler’s screwdriver to reinsert the small screw that holds the key fob together.
- Test the key fob to ensure proper functioning.
- If the key fob is not functioning properly, check for any loose parts or misalignment and repeat the battery replacement process as necessary.
By following these steps, you can safely and easily replace the battery in your Honda key fob and ensure the proper functioning of your keyless entry system.
Step 6: Testing the Key Fob
After replacing the battery and reassembling the key fob, testing it to ensure proper functioning is important. Follow these steps to test the key fob functionality:
- Stand near your vehicle and press the buttons on the key fob to lock and unlock the doors.
- If the doors lock and unlock properly, the key fob functions correctly.
- If the doors do not lock or unlock or the key fob does not respond, try replacing the battery again to ensure proper installation.
- If the key fob still does not work after replacing the battery, there may be other issues with the key fob or the keyless entry system. Consider consulting a trusted mechanic or electronics specialist for further assistance.
By testing the key fob after battery replacement, you can ensure proper functioning of your keyless entry system and avoid any potential issues with accessing your vehicle.
Read Also: What Does Hrv Stand For Honda
Final Thoughts!
Replacing the battery in your Honda key fob is a simple process that can be done with a few basic tools and a replacement battery.
Following the step-by-step guide outlined above, you can safely and easily replace the battery in your key fob and ensure the proper functioning of your keyless entry system.
Remember to identify the positive and negative terminals properly, clean the battery compartment, and test the key fob after battery replacement to ensure proper functioning.
If you encounter any issues during the battery replacement process, don’t hesitate to consult a trusted mechanic or electronics specialist for further assistance.
Related Articles:-
